IPhone 6 Plus Screen Replacement

Error

Difficulty

Hard

Steps

24

Time Required

2 hours

Introduction

This guide is for a screen replacement for the iPhone 6 Plus

Tools Required

Phillips #000 Screwdriver

P2 Pentalobe Screwdriver

Spudgers

Tweezers

iPhone opening tool

Parts

Error

LCD Screen for iPhone 6 Plus

$40.00

Buy

You can contact us to book an appointment should you find the guide too difficult to follow

Precautions

• Work on a clear and open surface • Careful when unscrewing as most of the screws are extremely small, have a small box ready with you • Take note and keep track of each screw during disassembling and assembling

Step 1
Error

Power off your iPhone before beginning disassembly. Remove the two 3.6 mm P2 Pentalobe screws next to the Lightning connector.

Step 2
Error
Error
Error
Error

Close the handle on the opening tool, opening the suction-cup jaws. Place you iPhone in between the suction cups, against the plastic depth gauge. Open the handles to close the jaws of the opening tool. Center the suction cups and press them firmly onto the top and bottom of the iPhone. Hold onto your iPhone securely and close the handle of the opening tool to separate the suction cups, pulling the front panel up from the rear case. Peel the two suction cups off your iPhone.

Step 3
Error

Pull the home button end of the front panel assembly away from the rear case, using the top of the phone as a hinge.

Step 4
Error

Remove the following Phillips screws from the battery connector bracket: One 2.3 mm screw (Red Circle) One 3.1 mm screw (Yellow Circle)

Step 5
Error

Remove the metal battery connector bracket from the iPhone.

Step 6
Error

Use the spudger to gently pry the battery connector up from its socket on the logic board.

Step 7
Error

Remove the following Phillips screws securing the front panel assembly cable bracket: Three 1.2 mm screws (Yellow Circle) One 1.5 mm screw (Red Circle) One 2.9 mm screw (Orange Circle)

Step 8
Error

Remove the front panel assembly cable bracket from the logic board.

Step 9
Error
Error
Error
Error

Use a spudger or a fingernail to disconnect the three front panel assembly cables in below order: 1. Front-facing camera and earpiece speaker connector 2. Disconnect the home button cable connector. 3. Display data cable connector. Remove the front panel assembly from the rear case.

Step 10
Error

Remove the two 1.8 mm Phillips screws securing the home button bracket to the front panel.

Step 11
Error

Remove the home button bracket from the front panel assembly.

Step 12
Error
Error
Error

Use the tip of a spudger to disconnect the home button connector from its socket on the home button cable.

Step 13
Error

Using your fingertip, gently press up on the home button from the front side of the display assembly. Use firm, constant pressure to slowly separate the home button's rubber gasket from the front panel. Carefully use the tip of a spudger to finish separating the home button from the front panel. Place back the home button into the new screen

Step 14
Error
Error
Error

Connect back the home button connector to its socket

Step 15
Error

Place back the home button bracket onto the front panel assembly.

Step 16
Error

Secure back the two 1.8 mm Phillips screws to secure the home button bracket to the front panel.

Step 17
Error
Error
Error
Error

Connect back the three front panel assembly cables in below order: 1. Display data cable connector. 2. Disconnect the home button cable connector. 3. Front-facing camera and earpiece speaker connector.

Step 18
Error

Place back the front panel assembly cable bracket onto the logic board.

Step 19
Error

Secure back the following Phillips screws to secure the front panel assembly cable bracket: Three 1.2 mm screws (Yellow Circle) One 1.5 mm screw (Red Circle) One 2.9 mm screw (Orange Circle)

Step 20
Error

Connect back the battery connector onto its socket on the logic board.

Step 21
Error

Place back the metal battery connector bracket

Step 22
Error

Secure back following Phillips screws: One 2.3 mm screw (Red Circle) One 3.1 mm screw (Yellow Circle)

Step 23
Error

Close back the iphone screen

Step 24
Error

Secure back the two 3.6 mm P2 Pentalobe screws next to the Lightning connector.


Troubleshooting