IPhone 6S Battery Replacement

Error

Difficulty

Hard

Steps

25

Time Required

2 hours

Introduction

This guide is for a battery replacement for the iPhone 6S

Tools Required

Phillips #000 Screwdriver

P2 Pentalobe Screwdriver

Spudgers

Tweezers

iPhone opening tool

Hair dryer

Nylon String

Parts

Error

Battery for iPhone 6S

$20.00

Buy

You can contact us to book an appointment should you find the guide too difficult to follow

Precautions

• Work on a clear and open surface • Careful when unscrewing as most of the screws are extremely small, have a small box ready with you • Take note and keep track of each screw during disassembling and assembling

Step 1
Error

Power off your iPhone before beginning disassembly. Remove the two 3.4 mm P2 Pentalobe screws on the bottom edge of the iPhone, next to the Lightning connector.

Step 2
Error

Note: The screen is secured to the chassis using adhesive Use hair dryer to soften adhesive

Step 3
Error
Error
Error
Error

Close the handle on the opening tool, opening the suction-cup jaws. Place you iPhone in between the suction cups, against the plastic depth gauge. Open the handles to close the jaws of the opening tool. Center the suction cups and press them firmly onto the top and bottom of the iPhone. Hold onto your iPhone securely and close the handle of the opening tool to separate the suction cups, pulling the front panel up from the rear case. Peel the two suction cups off your iPhone. Gently grasp the display assembly and lift it up to open the phone, using the clips at the top of the front panel as a hinge.

Step 4
Error

Remove two Phillips screws securing the battery connector bracket, of the following lengths: One 2.9 mm screw (Orange Circle) One 2.2 mm screw (Red Circle)

Step 5
Error

Remove the battery connector bracket from the iPhone.

Step 6
Error

Use the point of a spudger to disconnect the battery connector by prying it straight up from the logic board. Push the battery connector away from the logic board until it stays separated from its socket, so as to avoid any accidental connection to the battery while you work.

Step 7
Error

Remove the following four Phillips screws securing the display cable bracket: Three 1.2 mm screws (Yellow Circle) One 2.8 mm screw (Red Circle)

Step 8
Error

Remove the display cable bracket.

Step 9
Error
Error
Error
Error

Use a spudger or a fingernail to disconnect the three front panel assembly cables, in following orders: 1. Front camera flex cable 2. Digitizer cable 3. Display data cable connector. Remove the display assembly.

Step 10
Error
Error
Error
Error

Note: Battery is glued to the chassis of iphone Slightly pry up the top of the battery Insert nylon string between battery and chassis Slowly remove the adhesive

Step 11
Error

Remove the old battery Insert new battery

Step 12
Pasting waterproof adhesive
Error

Note: Steps 12 - 18 optional to replace waterproof adhesive

Step 13
Error

Begin by removing all the old display adhesive around the perimeter of your iPhone's case. Be sure to remove any remaining adhesive from the back of your display as well.

Step 14
Error

Begin peeling the large backing from your replacement adhesive, starting from the bottom edge.

Step 15
Error
Error
Error

Carefully align the exposed lower edge of the adhesive strip with the bottom edge of your iPhone's case. When it's correctly aligned, gently press the exposed lower adhesive strip into place.

Step 16
Error
Error
Error
Error

Continue peeling away the backing from the adhesive, gently pressing the adhesive into place from the bottom of your iPhone to the top. Finish separating the adhesive backing and discard it.

Step 17
Error
Error
Error
Error

Use the tip of a spudger to press all the adhesive into place around the entire perimeter of your iPhone.

Step 18
Error
Error
Error
Error

Completely separate the front adhesive liner(s) and discard it.

Step 19
Error
Error
Error
Error

Connect back the display assembly. Use a spudger or a fingernail to connect the three front panel assembly cables, in following orders: 1. Display data cable connector. 2. Front camera flex cable 3. Digitizer cable

Step 20
Error

Place back the display cable bracket.

Step 21
Error

Secure back the following four Phillips screws to secure the display cable bracket: Three 1.2 mm screws (Yellow Circle) One 2.8 mm screw (Red Circle)

Step 22
Error

Connect back the battery connector to the logic board.

Step 23
Error

Place back the battery connector bracket

Step 24
Error

Secure back the two Phillips screws securing the battery connector bracket, of the following lengths: One 2.9 mm screw (Orange Circle) One 2.2 mm screw (Red Circle)

Step 25
Error

Close back the iPhone Secure back the two 3.4 mm P2 Pentalobe screws on the bottom edge of the iPhone, next to the Lightning connector.


Troubleshooting