IPhone 6S Plus Battery Replacement
Introduction
This guide is for a battery replacement for the iPhone 6S Plus
Tools Required
• Phillips #000 Screwdriver
• P2 Pentalobe Screwdriver
• Spudgers
• Tweezers
• iPhone opening tool
• Hair dryer
• Nylon String
Parts
Battery for iPhone 6S Plus
S$18.80
Buy
You can contact us to book an appointment should you find the guide too difficult to follow
Precautions
• Work on a clear and open surface • Careful when unscrewing as most of the screws are extremely small, have a small box ready with you • Take note and keep track of each screw during disassembling and assembling
Step 1
Power off your iPhone before beginning disassembly. Remove the two 3.4 mm Pentalobe screws on either side of the Lightning port.
Step 2
Apply mild heat to the lower edge of the iPhone using hair dryer for about a minute.
Step 3
Close the handle on the opening tool, opening the suction-cup jaws. Place you iPhone in between the suction cups, against the plastic depth gauge. Open the handles to close the jaws of the opening tool. Center the suction cups and press them firmly onto the top and bottom of the iPhone. Hold onto your iPhone securely and close the handle of the opening tool to separate the suction cups, pulling the front panel up from the rear case. Peel the two suction cups off your iPhone. Gently grasp the display assembly and lift it up to open the phone, using the clips at the top of the front panel as a hinge.
Step 4
Gently grasp the display assembly and lift it up to open the phone, using the clips at the top of the front panel as a hinge.
Step 5
Remove two Phillips screws securing the battery connector bracket to the logic board, of the following lengths: One 2.9 mm screw (Red Circle) One 2.3 mm screw (Orange Circle)
Step 6
Remove the battery connector bracket.
Step 7
Use a spudger or a clean fingernail to disconnect the battery connector by prying it straight up off the logic board.
Step 8
Remove the following Phillips screws: Three 1.3 mm screws (Orange Circle) One 1.6 mm screw (Red Circle) One 3.0 mm screw (Yellow Circle)
Step 9
Remove the display cable bracket.
Step 10
Use the spudger to disconnect the four front panel assembly cables: Front-facing camera and sensor cable Display data cable connector Home button cable
Step 11
Remove the display assembly.
Step 12
Note: Battery is glued to the chassis of iphone Slightly pry up the top of the battery Insert nylon string between battery and chassis Slowly remove the adhesive
Step 13
Remove the old battery
Step 14
Paste battery adhesive on new battery
Remove the small blue tab
Step 15
Paste the black portion of the tape to the bottom front of the battery
Step 16
Peel away the plastic sheet
Step 17
Paste the adhesive to the back of the battery
Step 18
Peel away the plastic sheet
Step 19
Paste the new battery on the chassis Make sure battery connector is aligned to the socket
Step 20
Pasting waterproof adhesive
Note: Steps 20 - 24 optional to replace waterproof adhesive Begin by removing all the old display adhesive around the perimeter of your iPhone's case. Be sure to remove any remaining adhesive from the back of your display as well.
Step 21
Begin peeling the large backing from your replacement adhesive, starting from the bottom edge. Carefully align the exposed lower edge of the adhesive strip with the bottom edge of your iPhone's case. When it's correctly aligned, gently press the exposed lower adhesive strip into place.
Step 22
Continue peeling away the backing from the adhesive, gently pressing the adhesive into place from the bottom of your iPhone to the top. Finish separating the adhesive backing and discard it.
Step 23
Use the tip of a spudger to press all the adhesive into place around the entire perimeter of your iPhone.
Step 24
Completely separate the front adhesive liner(s) and discard it.
Step 25
Connect back the display assembly. Use a spudger or a fingernail to connect the three front panel assembly cables, in following orders: 1. Home button cable 2. Display data cable connector 3.Front-facing camera and sensor cable
Step 26
Place back the display cable bracket.
Step 27
Secure back the following Phillips screws: Three 1.3 mm screws (Orange Circle) One 1.6 mm screw (Red Circle) One 3.0 mm screw (Yellow Circle)
Step 28
Connect back the battery connector to the logic board.
Step 29
Place back the battery connector bracket
Step 30
Secure back the two Phillips screws: One 2.9 mm screw (Red Circle) One 2.3 mm screw (Orange Circle)
Step 31
Close back the iPhone
Step 32
Secure back the two 3.4 mm P2 Pentalobe screws on the bottom edge of the iPhone, next to the Lightning connector.